| Size |
60 / 90 / 120 cm |
| Controls |
3s + B Touch Control |
| Total Absorption |
265 W |
| Voltage |
220 - 240W |
| Lighting |
Led 2x2,5 W 4000 K |
| Finishes |
Stainless Steel + Glass |
| Duct Size |
150mm |
| Noise Level |
51-69db(A) |
| Booster Airflow |
350-1000 m3/h |
| Version |
Duct Out |
| Energy Class (EU) |
B |
All the technical data are based on manufacturer Italy 🇮🇹 Elica latest catalogues or data sheets, The airflow data is measured by factory lab. at the motor outlet points, it is a Free Motor Blower Value but not the EU testing method with exhaustion tube. All the cooker hoods and appliances specifications are subject to stock model or factory latest update. Please check the final offer from our quotation or offer to confirm the final specifications.
所有技術資料由意大利 Elica 最新產品目錄取得。所有 Elica 油煙機風速量度標準是根據摩打出風口量度並不是歐洲測試加上管導測試標準,所有規格廠方會恆常更新,我們會盡量更新準確資料,客人請參考購買貨物時规格, 貨物規格按現貨規格或訂貨廠方最新更新為準。
| ACCESSORIES |
|
| Long Life Filter |
F00262/3S |
| Charcoal Filter |
F00333/S |
| MODEL |
|
| TOP IXBL/A/60 |
PRF0110506 |
| TOP IXBL/A/90 |
PRF0110505 |
| TOP IXBL/A/120 |
PRF0110507 |
DOWNLOAD
Instruction Menu
Operation
Use the high suction speed in cases of concentrated kitchen vapours. It is recommended that the cooker hood suction is switched on for 5 minutes prior to cooking and to leave in operation during cooking and for another 15 minutes
approximately after terminating cooking.
To select the functions of the hood just touch the commands.
Light key ON/OFF
Intensive speed selection key (suction power) - duration 5 minutes: the hood sets this power and at the end of the 5 minutes returns to the previous setting.
High-speed selection key (suction power).
Medium-speed selection key (suction power)
- when flashing it indicates the need to wash or replace the carbon filter. This signal is normally deactivated. To activate the alarm, disable the electronic by pressing the 0 button for 3 seconds.
Next, simultaneously press buttons 1 and 2 for 3 seconds; at first, only button 1 will flash, then both buttons 1 and 2 will flash to indicate activation. Repeat the procedure to deactivate the alarm; at first buttons 1 and 2 will flash and subsequently only button 1 to indicate deactivation.
Low-speed selection key (suction power) – when flashing it indicates the need to wash the fats filter.
Motor key OFF (stand by) – excludes the electronics – reset wash/replace filters signals. MOTOR OFF Press briefly to switch the motor off.
RESET FILTERS SIGNALS
In functioning mode, after carrying out filter maintenance, press the key until hearing the sound signal. The flashing LED 1 (grease filter) or 2 (carbon filter) stops flashing.
EXCLUDING THE ELECTRONICS
Press the key for 3 seconds. The hood command electronics will be excluded.
This function can be useful during the product cleaning operations. Just repeat the operation to reinsert the electronics. If the hood fails to operate correctly, briefly disconnect it from the mains power supply for almost 5 sec. by pulling out the
plug. Then plug it in again and try once more before contacting the Technical Assistance Service.
Maintenance
ATTENTION! Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse. Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket.
Cleaning
The cooker hood should be cleaned regularly (at least with the same frequency with which you carry out maintenance of the fat filters) internally and externally. Clean using ONLY the cloth dampened with neutral liquid detergent. DO NOT CLEAN WITH TOOLS OR INSTRUMENTS. Do not use abrasive products. DO NOT USE ALCOHOL!
Warning! Failure to carry out the basic cleaning recommendations of the cooker hood and replacement of the filters may cause fire risks. Therefore, we recommend observing these instructions. The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations.
Grease filter
Fig. 10-27 Traps cooking grease particles.
This must be cleaned once a month (or when the filter saturation indication system – if envisaged on the model in possession – indicates this necessity) using non aggressive
detergents, either by hand or in the dishwasher, which must be set to a low temperature and a short cycle. When washed in a dishwasher, the grease filter may discolour slightly, but this does not affect its filtering capacity. To remove the grease filter, pull the spring release handle.
Charcoal filter (filter version only)
Fig. 26
It absorbs unpleasant odours caused by cooking.
The activated charcoal filter can be one of these types:
• Washable activated charcoal filter.
• NON-washable activated charcoal filter.
Washable activated charcoal filter
The charcoal filter can be washed once every two months using hot water and a suitable detergent, or in a dishwasher at 65°C (if the dishwasher is used, select the full cycle function and leave dishes out). Eliminate excess water without damaging the filter, then remove the mattress located inside the plastic frame and put it in the oven for 10 minutes at 100° C to dry completely. Replace the mattress every 3 years and when the cloth is damaged.
NON-washable activated charcoal filter
The saturation of the charcoal filter occurs after more or less prolonged use, depending on the type of cooking and the regularity of cleaning of the grease filter. In any case it is necessary to replace the cartridge at least every four months.
The charcoal filter may NOT be washed or regenerated.
Assembly
Hook the charcoal filter at the back on the metal tongue of the hood first, then on the front with the two knobs.
Disassembly
Remove the charcoal filter by turning the knobs fixing it to the hood by 90°.
Replacing lamps
Fig. 28
The hood is equipped with a lighting system based on LED technology. The LEDs guarantee an optimum lighting, a duration up to 10 times as long as the traditional lamps and allow to save 90% electrical energy. To purchase spare LEDs, contact the technical assistance service.
